back, no sensible pressure on the levers is produced, but only just enough to turn this protector lever, as Hobbs called it, on its pivot c, and so bring down its end a in front of the square pin, and then the bolt can no more be pushed back than when held by Chubb's detector. The protector is set free again by merely pushing the bolt forward with the key, without reference to the

J, r ' levers. However, the protector could g!, ,A Z 0% be prevented from acting by a method used by the inventor himself for another

1-f-f purpose, viz., by pushing a piece of watch-spring through the keyhole, and

W F up behind the bolt, so as to reach the protector at a, and keep it up while the

bolt was pushed back, or, again, by

pushing up the watch-spring between

any two of the levers, and holding

the end b of the protector with it, so as to press the stump against the levers. Both these devices, however, are prevented now by letting in a feather FF in a groove between the bolt and the bac of the lock, which no watch-spring can pass, and also bringing a FIG. 11.

piece of the feather forward throu h the front ati of he l vers 1 g g n the

just under the stump. In this form the lock is safe against any mode of picking known. A lock possessing valuable features was invented in 1852 by Sir Edmund Beckett'-afterwards Lord Grimthorpe-but did not come into general use for commercial reasons. All the locks containing many levers so far described havea common defect in that the levers are moved in one direction b the Y

key and in the other by springs. But it not infrequently happens 1 that dirt or grease gets between the levers and causes two or more to stick together, in which case one of them is lifted too high and the bolt is prevented from operating. To overcome this difficulty locks, especially those intended for safes, have been made so that alternate levers move in opposite directions, the key having two bits on opposite sides. This construction entails that the key enter the body of the levers instead of passing below them, an arrangement that had previously been in use to reduce the space into which gunpowder could be packed through the keyhole.

The key locks chiefly used in English safes have been the ordinary lever lock with 6-8 or IO levers, Chubb's “ detector, " l-lobbs's Key '0cks “ protector " or variants of these. In the Yale lock, which reverts in some degree to the idea of the ancient Egyptian lock, America has produced one key lock which has come into almost univers;d use in that country and is certainly worthy of note. The employed, and has been superseded by the use of changeable key locks.

The first of these, invented, by Robert Newell in 184I, was introduced into Great Britain from America by Hobbs in 1851. A simpler form, the construction of which is clearly shown by fig. 13, was brought out by Hobbs, Hart & Co. The bolt of this lock, instead of the ordinary main stump, carries a set of sliders, PPS, one corresponding to each lever and each carrying a projection S corresponding to a portion of the main stump. It will be seen that if any key

FIG. 13.

key of this lock, shown full size at ka in fig. 12, is remarkably small, being stamped from a

having steps of certain lengths is inserted when the lock is unlocked and the bolt B thrown thereby, each slider will be raised to a height corresponding to that to which its lever is raised by the key, and the two fixed teeth CC will engage two of the teeth in the front of each slider, so that they will be held in place ready to enter the lever gatings when the same key is inserted.

A changeable key lock introduced by the Chatwood Safe Co. has no gatings in the levers, whose fronts are cut with teeth gearing into similar teeth cut in a set of disks carrying the gatings. The disks are mounted on a stud which can be moved by a key from the back of the lock in such a way that while the main stump is in the gatingskeeping the disks in position-the disks are carried forward out of gear with the levers; the key can then be removed and another V g, piece of flat steel and V, .

3? weighing only a small l, Z

in the Bramah lock, in order to move the bolt, g as s '; Sv g 0 If which is not shown in the ' l § § g % fi figure. That may be done I § % |. ~ .| I ' either as in Bramah locks , es& S § § %I 0 or by a tongue or bit "

attached to the end ab of i @ I »-Q

the barrel as in several Q g § ' %

” other locks. The barrel ' § F is prevented fron; bei;11g~ ' ~ "!!"'!§ 19. 12. turne, except y the Q ~, s' f

proper key, thus. The Eg, . (apparently) live plugs with spiral springs over them in fig. 12 , ,' ' % are really all divided at the cross line bc, being all now lifted to the / proper height by the key. Consequently the barrel abc can turn § , § -'fe round, as there is no plug either projecting from it or projecting into 1 f ' § : it. But when the key is out, all the plugs are pushed down by the § ' % springs, and so the upper ones descend into the barrel and hold it ;§ % fast. And again, if any of the steps of a false key are too high, some Q ~ % of the lower plugs will be pushed up beyond the barrel into the holes lg 5 3% above them, and so the barrel cannot turn. The bevelled end of the O '9 H key near a enables it to be pushed in under the plugs, though with , ,, . s , ,'., ,, ,, .', , § “'““'“ some friction and resistance. %

It is frequently convenient to have a number of different locks so arranged thait, whilst each has its own individual, key, yet one special ' Zor master key will operate any of the series. In warded locks this is done by “ differing " the wards of the individual locks so that each key will only pass its own lock, and then Filing away the bit of an extra key so that it will pass all the wards; the objection to this method is that any of the individual keys can easily be filed away and so form a master key. A better method, which meets this objection, consists in making all the levers except one-or if need be two-of each lock alike and cutting another gating or widening the gating in the differing levers, so as to pass the master key which has one-or two-special steps.

The growth of safe deposits has called for special locks so that when a box changes tenants the outgoing tenant's key shall be useless. In some cases the locl: has been taken off and another substituted, but this is a clu nay makeshift now rarely Fig. 14.

having steps of suitable length inserted and turned so as to raise the levers, the disks being then brought back into gear. Both the above locks require that the key steps should have certain definite lengths corresponding to the teeth, but a later lock resembling to some extent that brought out by Hobbs, Hart & Co. has been introduced by the Chatwood Co., in which it is sufficient after unlocking the lock to file any of the key steps and so alter the pattern of the key in any wa In this lock, which is illustrated in fig. 14, unlike all those that have been described, the levers are not pivoted but slide upon guide stumps; the main stump is divided as in Hobbs Hart's lock, the various pieces being clamped together by a screw to form a solid stump. The sliders composing the main stump are not

provided with teeth, the changing being effected as follows: when