Take the last strand c round the end of b and through the bight made by a. Haul the ends taut.

Single Wall Crowned (fig. 24).-Form a sincgle wall, and lay one of the ends, a, over the knot. Lay b over a, an c over b and through the bight of a. Haul the ends taut.

F IG. 22. FIG. 23. FIG. 24.

Double Wall and Double Crown (ng. 25).-Form a single wall crowned; then let the ends follow their own parts round until all the parts appear double. Put the ends down through the knot. Matthew Walker (figs. 26, 27).-Unlay the end of a rope. Take the first strand round the rope and through its own bight; the second strand round the rope, through the bight of the first, and through its own bight; the third through all three bights. Haul the ends taut.

Inside Clinch (fig. 28).-The end is bent close round the standing part till it forms a circle and a half, when it is securely seized at a, b and e, thus making a running eye; when taut round anything it jams the end. It is used for securing hemp cables to anchors, I

I

/" iQ,

1

555 'Q

• thi 2

g/

i

3 5

0,0 3

|

Fig. 25. FIG. 26. FIG. 27. Fig. 28. the standing parts of topsail sheets, and for many other purposes. If the eye were formed outside the bight an outside clinch would be made, depending entirely on the seizings, but more ready for slipping.

Midshipmanir Hitch (Hg. 29).-Take two round turns inside the bight, the same as a half-hitch repeated; stop up the end or let another half-hitch be taken or held by hand. Used for hooking a tackle for a temporary purpose.

Turk's Head (g o -With fine line verv d 3). ' (ry) make a clove

hitch round the rope; cross the bights twice, passing an end the reverse way (up or down) each time; then keeping the whole spread fiat, I

it

sas saw

5€5»'| into

qv 'Q 6 /~ G;'!§ 5.

9 gc stag;-2 g n' iv

Q °z@* gg

E f . 6f'¢nf}

% 1

(|“"~

Fig. 29. Fig. 30. FIG. 31. FIG.32.

let each end follow its own part round and round till it is too tight to receive any more. Used as an ornament variously on side-ropes and foot-ropes of jibbooms. It may also be made with three ends, two formed by the same piece of line secured through the rope and one single piece. Form with them a diamond knot; then each end crossed over its neighbour follows its own part as above. Spanish Windlass (fig. 3I).~An iron bar and two marling-spikes are taken; two parts of a seizing are twisted like a cat's-paw (fig. 16), passed round the bar, and hove round till sufficiently taut. In eaving shrouds together to form an eye two round turns are taken with a strand and the two ends hove upon. When a lever is placed between the parts of a long lashing or frapping and hove round, we have what is also called a Spanish windlass. Slings (ng. 32).—This is simply the bight of arope turned up over its own part; it is frequently made of chain, when a shackle (bow u) takes the place of the bight at s and another at y, connecting the two ends with the rt which goes round the mast-head. Used to sling lower yardsf Fir boat's yards it should be a grummet with a thimble seized in at y. As the tendency of all yards is to cant forward with the weight of the sail, the part marked by an arrow should be the fore-side-easily illustrated by a round ruler and a iece of twine.

p Sprit-Sail Sheet Knot (fig. 33).-This knot consists of a double wall and double crown made by the two ends, consequently with six strands, with the ends turned down. Used, formerly in the clews of sails, now as an e§ cellen3 st;>p§ er, da laihing or shackle being placed at s and a lanyar roun the ea at

Turning in a Dead-Eye Cutter-Stay fashion (fig. 34).-A bend is made in the stay or shroud round its own part and hove together W

has

%

~ - ¢ 4 ”

¥., 1 47) 1

Z sés' 1

5 I 'O *§ @)

5 I hes I, 0

I ll- 9 I

1 f 55, f . f I

5 2 2 . 'Q .4

%§

FIG. 33. FIG. 34. FIG. 35.

with a bar and strand; two or three seizings diminishing in size (one round and one or two either round or fiat) are hove on taut and snug, the end being at the side of the fellow part. The dead-eye is put in and the eye driven down with a commander. Turning in a Dead-Eye end up (fig. 35).-The shroud is measured round the dead-eye and marked where a throat-seizing is hove on; the dead-eye is then forced into its place, or it may be put in first. The end beyond a is taken up taut and secured with a round seizing; higher still the end is secured by another seizing. As it is important that the lay should always be kept in the rope as much as possible, these eyes should be formed conform ably, either right-handed or left-handed. It is easily seen which way a rope would naturally kink by putting a little extra twist into it. A shroud whose deadeye is turned in end up will bearafairer strain, but is more dependent on the seizings; the under turns of the throat are the first to break and the others the first to slip. With the cutter-stay fashion the standing part of the shroud gives way underthe nip of the eye. A rope will afiord the greatest resistance to strain when secured round large thimbles with a straight end and a sufficient number of flat or racking seizings, To splice shrouds round dead-eyes is objectionable on account of opening the strands and admitting water, thus hastening decay. In small vessels, especially yachts, it is admissible on the score of neatness; in that case a round seizing is placed between the dead-eye and the splice. The dead-eyes should be in diameter 1% times the circumference of a hemp shroud and thrice that of wire; the lanyard should be half the nominal size of hemp and the same size as wire: thus, hemp-shroud 12 in., wire 6 in., dead-eye 18 in., lanyard 6 in.

Short Splice (fig. 36).-The most common description of splice is when a rope is lengthened by another of the same size, or nearly so. FIG. 36 represents a splice of

this kind: the strands have

been unlaid, married and

passed through with the assistance

of a marling-spike, over

one strand and under the next,

twice each way. The ends are

then cut off close. To render the splice neater the strands should have been halved before turning them in a second time, the upper half of each strand only being turned in; then all are cut oH smooth. Eye Si/¢rlice.—Unlay the strands and place them upon the same rope sprea at such a distance as to give the size of the eye; enter the centre strand (unlaid) under a strand of the rope (as above), and the other two in a similar manner on their respective sides of the first; taper each end and ass them through again. If neatness is desired, reduce the ends and) pass them through once more; cut off smooth and serve the part disturbed tightly with suitable hard line. Uses too numerous to mention. Cut Splice.—Made in a. similar manner to an eye splice, but of two pieces of rope, therefore with two splices. Used for mast-head pendants, jib-gu s, breast back stays, and even odd shrouds, to keep the eyes of the rigging lower b one part. It is not so strong as two separate eyes. Horseshoe Splicer-Made similar to the above, but one part much shorter than the other, or another piece of rope is spliced across an eye, forming horseshoe with two long le s. Used for back-ropes on dolphin striker, back stays (one on each side) and cutter's runner pendants. Long Splice. -The strands must be unlaid about three times as much as for a short splice and married-care being taken to preserve the lay or shape of each. Unlay one of the strands still further and follow up

Fig. 36.